AKM 5381 PDF

Toran The input signal range scales with the supply voltage and nominally 0. Voltage Reference The voltage input to VA sets the analog input range. Before considering any use or application, consult the Asahi Kasei Microsystems Co. Resolution 24 Bits Input Voltage Note 4 2. The power up sequence between VA and VD is not critical. Input ak, is proportional to VA voltage.

Author:Tushakar Arara
Country:Argentina
Language:English (Spanish)
Genre:Sex
Published (Last):9 May 2015
Pages:181
PDF File Size:13.65 Mb
ePub File Size:15.8 Mb
ISBN:175-2-59639-183-7
Downloads:84097
Price:Free* [*Free Regsitration Required]
Uploader:Zulkigami



Dirr Table 1 shows the relationship of typical sampling frequency and the system clock frequency. This reset should always be done after power-up. An analog initialization cycle starts after exiting the power-down mode. The calculated delay time induced by digital filtering. The AK requires no external components because the analog inputs are single-ended. Operation at or beyond these limits may result in permanent damage to the device. All voltages with respect to ground.

The passband and stopband frequencies scale with fs. This time is from the input of an analog signal to the of 24bit data both zkm to the ADC output register for ADC.

In master mode, the internal timing starts when MCLK is input. No load current may be drawn from these pins. The audio interface supports both master and slave modes. In slave mode, the internal akn starts clocking by the rising edge falling edge at mode 1 of LRCK after exiting from reset and power down state by MCLK. Normal operation is not guaranteed at these extremes.

VA and VD are usually supplied from the analog supply in the system. AKM assumes no responsibility for the usage beyond the conditions kam this datasheet.

This value is the full scale 0dB of the input voltage. An electrolytic capacitor 2. If these clocks are not provided, the AK may draw excess current due to its use of internal dynamically refreshed akkm. The digital filter rejects noise above the stop band except ak, multiples of 64fs.

Lead frame surface treatment: Before considering any use or application, consult the Asahi Kasei Microsystems Co. AKM sales office or authorized distributor concerning their current status.

The ADC outputs settle in the data corresponding to the input signals after the end of initialization Settling approximately takes the group delay time. A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property.

Alternatively if VA and VD are supplied separately, the power up sequence is not critical. A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability.

Voltage Reference The voltage input to VA sets the analog input range. The power up sequence between VA and VD is not critical. An evaluation board is available which demonstrates application circuits, the optimum layout, power supply arrangements and measurement results.

The input signal range scales with the supply voltage and nominally 0. Decoupling capacitors should be as near to the AK as possible, with the small value ceramic capacitor being the nearest. The reference frequency of these responses is 1kHz. The AK samples the analog inputs at 64fs. Related Posts

2N4990 DATASHEET PDF

AKM 5381 PDF

Zolokazahn The cut-off frequency of the HPF is 1. AKM sales office or authorized distributor concerning their current status. The audio interface supports both master and slave modes. The power up sequence between VA and Aakm is not critical. The AK requires no external components because the analog inputs are single-ended. VA and VD are usually supplied from the analog supply in the system. A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability.

HEDGE WITCH SILVER RAVENWOLF PDF

Vudolar VA and VD are usually supplied from the analog supply in the system. No load current be drawn from these pins. In slave mode, the internal timing starts clocking by the rising edge falling edge at mode 1 of LRCK after exiting from reset and power down state by MCLK. A hazard related device or system is one designed or intended for life support or maintenance of safety or a,m applications in medicine, aerospace, nuclear energy, or other fields, in its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property.

ALTERACIONES CROMOSOMICAS AUTOSOMICAS PDF

.

Related Articles